HFM. Parts BM57 Brake Master Suits RHD Nissan Skyline Silvia Z32 ABS + Non ABS
Parts BM57 Brake Master - Suits RHD Nissan Skyline Silvia Z32 (ABS + Non ABS). Parts have re-developed their superseded Brake Master Cylinder with higher quality rubbers and internals, with a classic monochrome design.
With a whopping 17/16 Inch (27mm) piston bore size, this is the perfect application if you are looking to increase your braking performance and reduce that spongy feeling to give you a firmer brake pedal with less travel. Parts have included a Tapered Grub Screw so that this model can be applied to both ABS and NON-ABS vehicles. The dark colour of HFM. Parts Brake Masters come from their Geomet® coating. As well as providing some heat protection and environmental resistance, this coating is environmentally friendly as it contains no Chromium, the leftover solution is recycled and no chemicals are evaporated.
Specifications Split Point = 35kgf (498psi) x 0.4 TIP! - Soften your pedal feel by increasing the brake booster size. Nissan Z32 / 300ZX Nissan 180sx Nissan S13 Silvia Nissan S14 Silvia Nissan S14/200sx Nissan S15 Silvia Nissan S15/200sx Nissan Skyline R32 Nissan Skyline R33 Nissan Skyline R34. The product is suited for RHD models only. If you have ABS brakes, you will need to block the middle port with the provided tapered grub screw.
4-Piston Calipers are required due to the increase in fluid volume. 1x BM57 Brake Master Cylinder 1x Tapered Grub Screw. My brake lines feed from the top, can I still use this Brake Master? Parts Brake Master is designed with side ports, most brake lines can be massaged around until they reach the brake master's ports.
My brake lines feed from the bottom, can I still use this Brake Master? The fluid sensor connector is on the wrong side, what can I do? You can easily swap the sensor connector to either side of the HFM. Parts Brake Master by following these steps.
On the terminal side, push a small flat screwdriver in between the sensor connector and the bottom of the reservoir to lightly pry apart the lock tab. On the opposite side of the sensor connector, push through to pop it out. This is much easier to do prior to installation! I have a round (or other shape) fluid sensor connector, will it fit? No, our fluid sensor connector is rectangle (as shown in the product photo), in order to plug your existing fluid sensor connector into our one, you will need to cut your existing connector off and join the two exposed wires to individual spade terminals.
Then, you can push these onto our connector. Will the proportioning valve suit my car? The Sepcs for the HFM. Parts BM57 are "Split Point = 35kgf (498psi) x 0.4" which can suit the models listed depending on the vehicles brake and suspension set up, your brake bias may differ.
How will I know if this BM57 will suit my car? Racing is all about optimising for performance, unfortunately, the only reliable way is to test suitability on a racetrack. Modifying vehicles is a specialist task and requires the knowledge and experience of competent individuals to be conducted safely. We recommend this product be installed by a competent person.
NSK Clutch Release Throw Out Bearing. HFM 15/16 Big Bore Clutch Slave Cylinder - Suits RB25, RB26. HFM 3/4 Clutch Slave Cylinder - Suits S13 180SX / S14 / R32 GTS-T.HFM Dot Parts manufactures and sells parts that are for off road use only, are not streetlegal and do not conform to Australian road laws or ADR Laws unless otherwise stated in the listing. At this time we do NOT send via Australia Post. Note 2: Our couriers cannot deliver to PO Boxes, Locked Bags or Parcel Lockers. Please make sure when placing your order you change to a street address. This item is in the category "Vehicle Parts & Accessories\Car & Truck Parts & Accessories\Brakes & Brake Parts\Master Cylinders".
The seller is "hfmdotparts" and is located in this country: AU. This item can be shipped worldwide.Parts